The GS-N100-D is a high performance CO2 sensor that comes with a pitot sampling tube that is inserted into a duct. It is provided with tubing and an inline filter that allows the pitot tube to sample from return air ducts for DCV applications. The GS-N100-D time-tested and reliable BACnet MS/TP and Modbus RTU firmware is superior to competitive CO2 sensors. Its reliability makes it the only approved network duct mounted CO2 sensor for GreenTrol outdoor air controllers.
Duct Mount CO2 Sensor with Pitot Tube Pickup and In-line Replaceable Filter
Use with GreenTrol outdoor airflow controllers to provide advanced CO2-DCV or ASHRAE 62.1 compliant population-based DCV
Demonstrate compliance with ASHRAE Standards 62.1, 90.1 and 189.1
Satisfy LEED requirements
Maintain acceptable indoor air quality
NDIR CO2 sensing technology
0 to 2,000 ppm range
ABC logic ensures long-term calibration stability
Replaceable filter allows prevents sensor fouling in dirty environments
Isolated RS-485 output circuitry
Time-tested and reliable BACnet and Modbus firmware
Field selectable BACnet MS/TP or Modbus RTU protocols
DIP switch selectable baud rates
Attractive wall-mount package
Operates on 24 VAC/DC
Compatible with all GreenTrol application specific controllers
The GS-N100-D is a high performance CO2 sensor for today’s demanding DCV applications. It uses Telaire’s NDIR sensing technology and GreenTrol’s high performance signal processing circuitry.
A pitot tube pickup probe is provided that is easily inserted into the side of a duct. The pickup probe is typically installed in the return air duct near the air handler for single zone applications or in the return duct of individual spaces on multi-zone applications.
The GS-N100-D time-tested and reliable BACnet MS/TP and Modbus RTU firmware is superior to competitive CO2 sensors. Its reliablilty makes it the only approved network duct mounted CO2 sensor for GreenTrol outdoor air controllers.
When combined with a GreenTrol outdoor air controller, this CO2 sensor can be used to improve traditional CO2 demand control ventilation by using a unique control algorithm that resets the outdoor air setpoint between user defined upper and lower airflow limits (not damper positions) to maintain the space CO2 level. This control method eliminates the under- and over-ventilation that is prevalent with traditional CO2-DCV.
An even more advanced control method uses the measured airflow rate and CO2 level to estimate the population and calculates the required outdoor airflow, thus meeting the actual requirements of ASHRAE Standard 62.1.
Long term stability and high-performance components ensure years of trouble free performance.
CO2 Measurement: Provides the CO2 level in ppm via the network connection
System Status Alarm: Yes
Baud Rate, Protocol and Addressing: DIP switch
End of Line Termination: Jumper
Important: Modification of the factory default settings requires that power is cycled to the device. It is recommended that each device is bench configured prior to installation OR settings are provided at the time of order so that the device can be factory configured prior to shipment.
Technology: Telaire Non Dispersive Infrared (NDIR)
Range: 400 to 2,000 ppm
Sampling Method: Duct mounted pitot tube provided with two 3 foot tubes and inline filter
Required Duct Velocity: 300 to 1,500 FPM [1.52 to 7.62 m/s]
Accuracy: 400 to 1,250 ppm ±30 ppm or 3% of reading, whichever is greater 1,250 to 2,000 ppm ±5% of reading + 30 ppm
Temperature Dependence: 0.36% FS/°F [0.2% FS/°C]
Pressure Dependence: 0.33% of reading per 0.1 in. [2.54 mm] Hg
Stability: <2% of FS over life of sensor (15 year typical)
Calibration Interval: Not required when ABC logic is enabled
Response Time: <2 minutes for 90% step change typical
Signal Update: Every 4 seconds
Warmup Time: 2 minutes operational, 10 minutes to achieve maximum accuracy
Type: Isolated, field selectable MS/TP BACnet master or Modbus RTU connection
B.A.S. Object/Register Read/Write Access: Yes
Device Load: 1/8 load
Supported Baud Rates: 9.6, 19.2, 38.4 and 76.8 kbaud
Environmental Limits, Power Requirements & Dimensions
Temperature: 32 to 122 ⁰F [0 to 50 ⁰C]
Humidity: 5 to 95%
Power Requirement: 24 VAC (22.8 to 26.4 under load) @1.5V-A
Dimensions: 6.01H x 3.57W x 1.58D in. [152.6 x 90.7 x 40.1 mm]
Pitot Tube Length: 5.4 in. [137.2 mm]
156 Holly View Lane Loris, SC 29569 Toll Free 877 446 8765